Moates.Net Logo
(0)
. 00

My Account
Tuning Solutions for the Modern Gearhead
 

GM OBD1 Pre-1996 devices:

A collection of products which have been used on GM OBD1 vehicles for datalogging, reflashing, chip adaptation, chip programming, and realtime emulation.
Products
Displaying 1 to 28 (of 28 products) Result Pages:  1 
    Product Name   Price+   Buy Now 
 Flash & Burn Program for BURN1/2/Jaybird+APU1  Flash & Burn Program for BURN1/2/Jaybird+APU1
 This program is used to control the chip reading / erasing / writing duties of the Burn1, Burn2, Jaybird and APU1 devices. With it, you can read and write chips. Free of charge. 
     
 Battery for QH/Ost2/RR  Battery for QH/Ost2/RR
 You should never need a battery replacement on the Quarterhorse, Ostrich2, or Roadrunner, but if you do (if you short the old one out or something), then you can use this. Most units are soldered in, so be prepared to desolder the old one to replace it. If the old one measures over 2 volts then it should be fine so don't replace it! 
 $3.00  Buy Now 
 HDR1 Memcal Header  HDR1 Memcal Header
 Use this adapter to read the 'stock' binary from your TPI-style Memcal. Plugs into your 'stock' P4-style Memcals. Allows you to download your original 'factory' chip contents directly using a chip programmer/reader like the BURN1 or APU1. Very durable, and designed for repeated use. 
 $10.00  Buy Now 
 HDR6 Memcal Readout Header  HDR6 Memcal Readout Header
 For many GM/Holden applications that have a 32-pin EPROM with 128k file, this device can be used to retrieve the 'stock' calibration without damaging the memcal. 
 $10.00  Buy Now 
 APADC A/D Connector for APU1  APADC A/D Connector for APU1
 NOT NEEDED unless your APU1 has a firewire cable connector and no 4-pin screw terminal. All the new APU1s have this built in already! This is the APADC, which is a little break-out box with screw terminals and an interconnect cable for connecting up to three 0-5v analog inputs to the AutoProm. It has jumpers on it to allow a 0.3x gain so that you can hook up higher voltage (ca. 0-12v) as well. Comes with the 3 foot inteconnect cable to go between the terminals and the APU1. 
 $15.00  Buy Now 
 HDR5 Diesel Pin Header  HDR5 Diesel Pin Header
 This is basically an inverted G5 adapter. This piece allows you to 'read' or 'reprogram' (with appropriate chip programmer/eraser) those 'BLUE' chip modules from the GM 6.5L Diesel applications. A replacement chip adapter (G5) is available separately. 
 $15.00  Buy Now 
 EX Remote Switch /w/LED  EX Remote Switch /w/LED
 Remote switchbox for multi-bank setups like the G2X, GX, and G3. Has a red single-digit LED display to show which program bank is selected. It's about the size of a car alarm remote, with pushbuttons to select from different memory banks. Comes with 6-foot ribbon cable for remote mounting. Here is a video illustrating how to operate the unit: http://www.moates.net/tutorials/new_ex_v01.wmv 
 $25.00  Buy Now 
 <font size= 1>2TIMER</font>  2TIMER
 This little gem plugs into your 28-pin socket that normally takes a 27C128 or 27C256. It has a single wire lead coming off of it. Put a 27SF512 chip in it, and switch the wire lead to chassis ground to switch between two separate programs! Comes with a 27SF512 chip. 
 $30.00  Buy Now 
 CABL1 OBD1-Style ALDL Connector  CABL1 OBD1-Style ALDL Connector
 Does not work by itself! Needs the ALDU1 or APU1 to work.Works with pre-1995 GM ALDL ports. You need this to log data on your GM. Connects directly to AutoProm or ALDU1. Is used on most pre-1996 GM EFI cars. Does NOT work by itself! Requires the ALDU1 or APU1 to actually interface to the PC! 
 $30.00  Buy Now 
 CABL2 OBD2-Style ALDL Connector  CABL2 OBD2-Style ALDL Connector
 Does not work by itself! Needs the ALDU1 or APU1 to work.Used for datalogging and PCM reflash on 1995 LT1 setups. Connects directly to AutoProm or ALDU1. Is used primarily on 94/95 GM LT1s. Does NOT work by itself! Requires the ALDU1 or APU1 to actually interface to the PC! 
 $30.00  Buy Now 
 G2 Memory Adapter: 0.45" Leg Spacing  G2 Memory Adapter: 0.45" Leg Spacing
 Very rarely used! This is primarily ONLY used on the Grand Nationals. If you're not POSITIVE that you have the 0.45" spacing then get the 0.6" spacing. Allows use of new Flash chips in many GM TBI setups. If the original application accepted a 24-pin chip such as a 2732A, then this adapter will allow you to upgrade to new Flash chips such as the AT29C256 and 27SF512. Soldering required (see product web page). 
 $30.00  Buy Now 
 G2 Memory Adapter: 0.60" Leg Spacing  G2 Memory Adapter: 0.60" Leg Spacing
 Allows use of new Flash chips in many GM TBI setups. If the original application accepted a 24-pin chip such as a 2732A, then this adapter will allow you to upgrade to new Flash chips such as the AT29C256 and 27SF512. Soldering required (see product web page). 
 $30.00  Buy Now 
 G5 Memory Adapter  G5 Memory Adapter
 This is to replace those 'BLUE' chip modules in your 6.5L GM PCMs. This way you can just replace the blue piece instead of prying the old chip loose or messing with a UV eraser. An HDR5 is available separately if you want to read those stock chips (see product listings). 
 $30.00  Buy Now 
 G6 Adapter for Commodore/Holden  G6 Adapter for Commodore/Holden
 For many GM/Holden applications, this adapter will allow you to use the AM29F040 chip (C3) to contain your 128k calibrations. Up to 4 switchable programs with separate rotary switch and cable. Can also be used as an adapter to the Ostrich emulator. This unit REPLACES the stock memcal. 
 $30.00  Buy Now 
 Installation Service for non-Honda ECUs  Installation Service for non-Honda ECUs
 This is a service we offer for 'chipping' your ECU. We do NOT chip or install any of the Honda ECUs anymore, all that work is being referred to our partners at Xenocron, so check www.xenocron.com for details. 
 $30.00  Buy Now 
 G1 Memory Adapter: TPI ETC.  G1 Memory Adapter: TPI ETC.
 The G1 adapter bypasses your factory tuning, and lets you insert your own custom programmed chip without tearing up your stock memcal. Works with a wide range of GM chipped EFI applications, namely the 1986-1993 TPI & LT1 and the 94/95 TBI trucks. 
 $35.00  Buy Now 
 TunerView RD1 ALDL Link Interface  TunerView RD1 ALDL Link Interface
 This interface box allows you to hook up to the CABL1 ($30) and the TunerView and RD1 displays in order to datalog and monitor ALDL variables. Supported mask IDs include $8D and $59 as of 2/8/11. 
 $35.00  Buy Now 
 TunerPro RT V5  TunerPro RT V5
 TunerPro RT v5 covers all of the capabilities of the V4 software, as well as many new features including support for the Quarterhorse with Ford A9L and T4M0 datalogging. Advanced ADX configuration and plug-in support opens new doors for communications flexibility. This highly configurable software supports MANY vehicles including GMOBD1, Ford, Nissan, BMW, Porsche, and others. 
 $39.00  Buy Now 
 G2X TBI-Type Switching Adapter  G2X TBI-Type Switching Adapter
 This allows the GM TBI users who use 2732A 24-pin chips as their stock application to use a 29C256 or 27SF512 chip to hold multiple programs! Must be used in combination with the EX remote switch available separately. 
 $40.00  Buy Now 
 G4 Adapter for 94-95 stuff  G4 Adapter for 94-95 stuff
 This is for GM memcal-to-chip adaptation where you have the little blue 'box' memcal that has the integrated knock sensing board. Those little puppies are a real pain to hack apart, and this adapter makes it MUCH easier. Typically used on ECMs like the 16183247 and that sort of thing (Grand Am, Grand Prix, etc). Chip (C2 27SF512) sold separately. 
 $40.00  Buy Now 
 GX Switching Adapter for 28-Pin Sockets  GX Switching Adapter for 28-Pin Sockets
 This adapter snaps right down into a 28-pin socket that usually accepts a 29C256 or 27SF512 and allows you to switch among 8 or 16 different programs! Requires the EX remote switch and a C3 AM29F040 chip. 
 $40.00  Buy Now 
 ALDU1 XtremeALDL USB-to-ALDL Converter  ALDU1 XtremeALDL USB-to-ALDL Converter
 Does not work by itself, needs the CABL1 or CABL2 to work! USB-based ALDL converter box. Goes between your PC and a CABL1 or CABL2. Works great, unlike most USB/Serial converters. Goes straight from USB to ALDL. Does NOT work with a serial port. Compatible with all the popular programs in Windows (TunerPro, DataMaster, WinALDL). Will do 160-baud and 8192-baud communication. Not for use with the 'Moates' ECM852 software or other DOS-based programs. Self-powered via USB, and it has a built-in switch to select mode (up=10k, middle=open, down=short) for the A-B pins. Comes with a 6-ft USB cable, but requires either the CABL1 or CABL2 for connection to the car, depending on your application. The RJ-type-looking connector you see in the picture is for the CABL1 and CABL2, and it is not a standard RJ-type connector. 
 $50.00  Buy Now 
 GP1 Package: GM Adapter with 2 chips  GP1 Package: GM Adapter with 2 chips
 This package is very popular. It comes with two 27SF512 chips, an 'S2' ZIF socket, and a G1 adapter! This is everything you need for TPI/etc chip adaptation. If you want different chips or different socket, just purchase the pieces separately from the other items listed. 
 $55.00  Buy Now 
 'ALDU1 and CABL1'  'ALDU1 and CABL1'
 This is for any pre-1995 (OBD1) GM vehicle. Everything except the 1995 LT1. You should be able to datalog all of them, and reflash the 94 LT1 as well. Comes with XtremeALDL and NewCABL1 (RJ45/Moates-specific new style). There's a switch on the side which allows you to select 10k (across pins A&B of ALDL) or 'Open' mode. You use the 10k mode for older TBI and TPI setups, and the 'Open' for newer Speed density and LT1 stuff. This item can be used with TunerPro RT, TTS Datamaster, TunerCat reflash for LT1, WinALDL, and EFI Live V4(OBD1). 
 $80.00  Buy Now 
 'ALDU1 and CABL2' Combo  'ALDU1 and CABL2' Combo
 This is for any 1995 (OBD1) GM vehicle. Does the 1995 LT1. You should be able to datalog and reflash the 95 LT1. Comes with ALDU1 (not shown). Looks like OBD2 but it's not. 
 $80.00  Buy Now 
 'BURN2 Chip Programmer'  'BURN2 Chip Programmer'
 USB Chip Programmer works with the AT29C256, 27SF512, and AM29F040 chips. Self-powered from the USB port, so no power adapter is needed! Burner can also be used to read stock GM memcals using the HDR1 adapter. While it will only program the three types of chips listed, please note that those three chips can be used as drop-in replacements for most EFI applications. Comes with stand-alone chip programming software (available for download). Also compatible with TunerPro RT. Will read most stock-style chips (2732A, 27C128/256/512/etc). Mini-USB cable is included. 
 $85.00  Buy Now 
 'Ostrich 2.0 : The New Breed'  'Ostrich 2.0 : The New Breed'
 The newest breed of emulator has evolved! This is the newest Ostrich, the 2.0 unit. It is extremely small and compact, durable, versatile, and powerful. Full 921.6k speed, from 4k (2732A) up to 512k (4mbit 29F040) and everything in between (27C128, 27C256, 27C512). 
 $175.00  Buy Now 
 'APU1' AutoProm Package: USB Version  'APU1' AutoProm Package: USB Version
 Does everything in one package, one USB-based device! USB-powered, so no power supply needed. Chip burning/reading, datalogging, and realtime emulation. Performs ALDL communications at 160/8192 baud, programs AT29C256 and 27SF512 chips. Has 3-channel 0-5v 10-bit A/D provision fpr wideband and other datalogging. Includes AutoProm device, 28-pin 18-inch emulation cable, OBD1-style ALDL cable CABL1, 6-ft USB cable, 2x 27SF512 chip, and Mark Mansur's TunerPro RT5 software license. PLEASE READ through product documentation to understand some of the features of this all-in-one, datalogging, realtime emulation tuning, and chip burning hardware. This item is for OBD1 GM vehicles ONLY.  It is not for Hondas, Nissans, Fords, BMWs or other cars.  If you are not sure whether this unit is the right choice for you, please email support prior to purchase. 
 $329.00  Buy Now 
Displaying 1 to 28 (of 28 products) Result Pages:  1 

Copyright © 1999-2017 Moates.net